0
Owner's of the Black & Decker Power Screwdriver 3.6V SCREWDRIVER gave it a score of 0 out of 5. Here's how the scores stacked up:
7
(button pushed to the right) for removing
fasteners. When moving from forward to
reverse, or vice versa, always release the
trigger switch first. Release trigger when the
fastener is at the desired depth.
NOTE: For best performance, #8, 2” fasteners
are recommended, or screw into pre-drilled
holes (1/16 - 5/32 bit recommended).
DRILLING
• Insert the appropriate hex shank drill bit.
• Select forward rotation.
GENERAL DRILLING TIPS
• This tool is not recommended for drilling in
masonry.
• Use sharp drill bits only
• Drill bits for metal can be used for drilling
holes in wood. These bits must be sharp
and should be pulled out frequently when
drilling to clear chips from the flutes.
• Support and secure work properly, as
instructed in the safety Instructions.
• Use appropriate and required safety
equipment, as instructed in the safety
instructions.
• Secure and maintain work area, as
instructed in the safety instructions.
• Use light pressure until the hole is started
enough to keep the drill bit from slipping
out of it.
• Apply pressure in a straight line with the
bit. Use enough pressure to keep the bit
biting but not so much as to stall the motor
or deflect the bit.
• Hold the tool firmly to control its twisting action.
• DO NOT CLICK THE TRIGGER OF A
STALLED TOOL OFF AND ON IN AN
ATTEMPT TO START IT. DAMAGE TO
THE TOOL CAN RESULT. To remove:
• Put tool in reverse and back drill bit out.
• Turn tool off and back bit out by hand.
• Remove bit with pliers.
• Minimize stalling on breakthrough by
reducing pressure and slowly drilling
through last part of hole.
• Put tool in reverse while pulling the bit out of
a drilled hole. This will help reduce jamming.
• Make sure switch turns tool on and off.
WARNING: It is important to support
work properly and to hold the tool firmly to
prevent loss of control which could cause
personal injury.
MAINTENANCE
Use only mild soap and damp cloth to clean
the tool. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY
and RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this manual)
should be performed by authorized service
centers or other qualified service personnel,
always using identical replacement parts.
BATTERY REMOVAL AND DISPOSAL
This product uses lithium-ion rechargeable
and recyclable batteries. When the batteries
no longer hold a charge, they should be
removed from the product and recycled.
They must not be incinerated or compacted.
The batteries can be taken for disposal to
a BLACK+DECKER, Company-Owned or
Authorized Service Center. Some local
retailers are also participating in a national
recycling program (see “RBRC
TM
Seal”). Call
your local retailer for details. If you bring the
batteries to a BLACK+DECKER Company-
Owned or Authorized Service Center, the
Center will arrange to recycle old batteries.
Or, contact your local municipality for proper
disposal instructions in your city/town.
To remove the battery pack for disposal:
1.) First, before attempting to disassemble
the product, turn it on and run it in either
direction until it stops to ensure a complete
discharge of the batteries.
2.) Remove the screws in the product housing
and lift the housing half from the tool.
3.) Disconnect the terminal clips from the
batteries and lift the batteries out.
4.) Place the battery in suitable packaging
to prevent a short circuit of the battery
terminals.
5.) Dispose of batteries as per
recommended guidelines.
ACCESSORIES
Recommended accessories for use with
your tool are available from your local dealer
or authorized service center. If you need
assistance regarding accessories, please
call: 1-800-544-6986.
WARNING: The use of any accessory
not recommended for use with this tool could
be hazardous.
THE RBRC™ SEAL
The RBRC™ (Rechargeable
Battery Recycling Corporation)
Seal on the lithium-ion battery
(or battery pack) indicates that
the costs to recycle the battery (or battery
pack) at the end of its useful life have
already been paid by BLACK+DECKER.
In some areas, it is illegal to place spent
lithium-ion batteries in the trash or municipal
solid waste stream and the RBRC program
provides an environmentally conscious
alternative.
RBRC in cooperation with
BLACK+DECKER and other battery
users, has established programs in the
United States and Canada to facilitate the
collection of spent lithium-ion batteries.
Help protect our environment and conserve
natural resources by returning the tool to
an authorized BLACK+DECKER service
center for recycling. You may also contact
your local recycling center for information on
where to drop off the spent battery, or call
1-800-8-BATTERY.
SERVICE INFORMATION
All BLACK+DECKER Service Centers are
staffed with trained personnel to provide
customers with efficient and reliable power tool
service. Whether you need technical advice,
Find Your Products By Category
Please Login
