0
Owner's of the Campbell Hausfeld Car Stereo System NOT FOUND gave it a score of 0 out of 5. Here's how the scores stacked up:
7. Always use a pressure regulator on
the air supply to the spray gun.
Failure to install
appropriate
water/oil removal equipment may
result in damage to machinery or
workpiece.
Do not misuse this
product. Excessive
exposure to vibration, work in
awkward positions, and repetitive
work motions can cause injury to
hands and arms. Stop using any tool if
discomfort, numbness, tingling, or pain
occur, and consult a physician.
CALIFORNIA PROPOSITION 65
You can create dust when
you cut, sand, drill or grind
materials such as wood,
paint, metal, concrete,
cement, or other masonry. This dust
often contains chemicals known to
cause cancer, birth defects, or other
reproductive harm. Wear protective
gear.
Set Up
USE OF AIR CAPS
Internal Mix—Generally
used with slow drying,
heavy bodied materials
and for faster material
application. NOT to be
used with fast drying paints and
lacquers which will clog the opening in
the air cap.
INTERNAL MIX CAPS
MUST BE USED WITH PRESSURE
FEED OPERATION.
External Mix—Used for
quick drying, light bodied
materials such as lacquers
and synthetic enamels.
Better for finer finish work.
THESE CAPS CAN BE USED WITH
EITHER SIPHON OR PRESSURE FEED.
FAN DIRECTION
The direction of the fan (horizontal or
vertical) can be changed by loosening
the lock ring and turning the air cap 90
degrees (See Figure 1). Hand tighten
lock ring after adjustment.
!
DANGER
!
WARNING
NOTICE
Model Descriptions
(Cont.)
• Adjusts for vertical or horizontal
patterns.
NOTE: This gun cannot be used with a
paint tank.
MODEL DH3800
• Comes from the factory as a pressure
feed, non-bleeder type; convertible
to bleeder type trigger actuation.
• Uses external mix air cap.
• Has fluid control knob.
• Adjusts for vertical or horizontal
patterns.
NOTE: This gun cannot be used with a
paint tank.
MODEL DH4200
• Comes from the factory as a pressure
feed, non-bleeder type; convertible
to siphon feed, bleeder type or any
combination of these types
• Uses internal or external mix air caps.
• Has fluid control knob.
• Adjusts for vertical or horizontal
patterns.
• May be used with a paint tank.
MODEL DH5300/IFS530
• Comes from the factory as a non-
bleeder, siphon feed, external mix
gun. Can be converted to bleeder,
pressure feed, internal mix type.
• Switches easily from siphon to
pressure feed with the twist of a
knob.
• Uses internal or external mix air caps.
• Has fluid control knob.
• Has pattern control knob.
• Adjusts for vertical or horizontal
patterns.
• May be used with a paint tank.
General Safety
1. Read all manuals
included with this
product carefully. Be
thoroughly familiar
with the controls and
the proper use of the equipment.
2. Follow all local electrical and safety
codes as well as in the United States,
the National Electrical Codes (NEC),
Occupational Safety and Health Act
(OSHA) and the Environmental
Protection Agency (EPA).
Safety glasses and ear
protection must be worn
during operation.
!
WARNING
2
General Purpose Spray Guns
Use a face mask/respirator
and protective clothing
when spraying. Always
spray in a well ventilated area to
prevent health and fire hazards. Refer
to Material Safety Data Sheets (MSDS)
of spray material for details.
Never spray closer than 25
feet to the compressor! If
possible, locate
compressor in separate room. Never
spray into the compressor, compressor
controls or the motor.
3. Do not smoke or eat when spraying
paint, insecticides, or other
flammable substances.
Do not spray flammable
materials in vicinity of
open flame or near
ignition sources. Motors, electrical
equipment and controls can cause
electrical arcs that will ignite a
flammable gas or vapor. Never store
flammable liquids or gases in the
vicinity of the compressor.
4. When spraying and cleaning, always
follow the instructions and safety
precautions provided by the material
manufacturer (Refer to MSDS).
Do not spray acids,
corrosive
materials, toxic chemicals, fertilizers or
pesticides. Using these materials could
result in death or serious injury.
5. Keep visitors away and NEVER allow
children or pets in the work area.
Never aim or
spray at yourself
or anyone else or serious injury could
occur.
6. Always work in a clean environment.
To avoid injury and damage to the
workpiece, do not aim the spray gun
at any dust or debris.
Do not use pressure that
exceeds the operating
pressure of any of the
parts (hoses, fittings, etc.) in the
painting system.
Keep hose away
from sharp
objects. Bursting air hoses may cause
injury. Examine air hoses regularly and
replace if damaged.
!
CAUTION
!
WARNING
!
WARNING
!
WARNING
!
WARNING
!
DANGER
!
WARNING
MANUAL
www.chpower.com
23 Sp
Modelos DH3200, DH3800, DH4200 y DH5300, IFS530
Guía de Diagnóstico de Averías
Problema Posible(s) Causa(s) Acción a Tomar
El patrón de rocío es
muy pequeño
El patrón de rocío es
inadecuado
Exceso de rocío
Fuga por la tuerca de
control de fluído
Fuga por el envase y la
tapa del envase
Cáscara de naranja
(apariencia de
ondulación áspera
semejante a una
cáscara de naranja real)
Chorreos y depresiones
Superficie con acabado
moteado y tosco
1. Acumulación de material
seco en los orificios de la tapa
de aire
2. Material aglutinado
3. Insuficiente cantidad de
material
4. Insuficiente presión de fluído
1. El material está muy espeso
2. La tapa de aire está sucia
3. Está aplicando mucho
material
4. El patrón es muy ancho
1. Demasiada presión de aire
para el tipo de material que
está aplicando
2. El material está muy diluído
1. El empaque está muy flojo
2. El empaque está desgastado
o reseco
1. El empaque del envase está
mal colocado
2. El envase no está bien
apretado
1. El material se está secando
muy rápido
2. Pistola muy lejos de la superficie
3. Material muy espeso
1. Material muy diluido
2. La pistola se está moviendo
muy lentamente
3. Flujo excesivo de material
4. Pistola muy cerca de la superficie
1. Demasiado solvente
2. Técnica deficiente de rociado
1. Limpie la tapa de aire
2. Diluya o cuele el material
3. Abra más la perilla de control de fluído
4. Aumente la presión de aire. No exceda 3,45 bar
1. Diluya el material
2. Límpiela
3. Cierre la perilla de control de fluído para reducir el flujo de
material
4. Cierre más la perilla de control de fluído o acerque más la
pistola a la pieza de trabajo
1. Reduzca la presión de aire
2. Mézclelo con material más espeso. Reduzca la presión de
aire. Gradualmente abra la perilla de control de fluído
1. Apriete la tuerca del empaque. Reemplace el empaque si no
puede parar la fuga al apretar la tuerca
2. Reemplácela o lubríquela con aceite sinsilicón
1. Limpie el empaque. Reeplácelo si es necesario
2. Apriételo bien. Aplique una pequeña cantidad de vaselina o
grasa mineral en las roscas cuando vaya a colocarle la tapa al
envase
1. Use un solvente más lento o añanda un agente retardante
2. Acerque la pistola a la superficie
3. Diluya el material según las instrucciones de cómo hacer
menos densos los materiales
1. Añada material para aumentar el espesor
2. Mueva la pistola más rápido
3. Gire la perilla de control de material en sentido horario para
reducir el flujo
4. Aleje más la pistola de la superficie
1. Disminuya el solvente
2. Refiérase a “Operación” para las instrucciones de rociado
Figure 1
Horizontal Fan
Vertical Fan
Air Cap
Lock Ring
Find Your Products By Category
Please Login
